Wicker vs Metal Patio Furniture: Aluminum, Steel and Rust
Wicker vs metal patio furniture: resin wicker wins on comfort, aluminum on low upkeep, steel and iron on weight. Compare rust, heat, UV and care.

As an Amazon Associate, Hiewigo earns from qualifying purchases. We never accept free products or payment for placement.
The short answer
- Most "wicker" patio sets are resin wicker on an aluminum frame, so the real choice is often woven look and soft seating versus a sleek all-metal frame.
- Aluminum does not rust and stays light; steel and wrought iron are heavy and rust once the finish chips.
- Natural rattan is an indoor or covered-porch material. Outdoors, look for UV-stabilized resin (PE) wicker.
- Pick by climate and effort: salt air and rain favor powder-coated aluminum, windy decks favor heavier frames, and hot sun favors wicker with shaded cushions.
On this page
Wicker vs metal patio furniture comes down to look, weight and upkeep: resin wicker feels softer and warmer, aluminum is the easiest metal to live with, and steel or wrought iron is the heaviest and the most demanding. Most woven sets are already built on a metal frame, so the choice is often about the finish you see. If you are comparing whole sets, our patio conversation set comparison of wicker and metal-frame sets puts the options side by side.
This guide sorts out the real differences between outdoor furniture materials: how each one handles rain, sun, heat and salt air, what maintenance it needs, and which suits your yard, your color preference and your dining or lounging layout.
What is wicker patio furniture made of?
Wicker is a weaving technique, not a single material. Outdoor wicker furniture is usually synthetic: strands of PE (polyethylene) resin woven around a frame, most often aluminum. Natural wicker is woven from rattan, bamboo or willow and is meant for covered, dry spaces.
That distinction matters because the phrase “wicker vs metal” hides a trap. A resin wicker set is usually not an alternative to metal at all; the frame underneath is typically powder-coated aluminum, and only the visible surface is woven. A few lower-cost sets use a steel frame instead, which is where rust shows up later.
Rattan is a material, wicker is a weave
Rattan is a vine, and it can be woven into wicker. Resin wicker copies that look with a weatherproof plastic strand, so it behaves very differently in rain and sun than the natural version.

What metals are used for patio furniture?
Most metal patio furniture is made from aluminum, steel or wrought iron, with a powder-coated finish over the metal. Aluminum is the most common frame in current sets, steel appears in lower-cost and heavier pieces, and wrought iron is the classic ornate look.
The powder coating, a baked-on dry paint, is the real shield. It keeps water off the metal, so a frame’s weak points are chips, scratches and welds rather than the metal itself. Steel and iron sets need regular cleaning, waxing and chip touch-ups to stay rust-free.
| Material | Rusts? | Weight |
|---|---|---|
| Cast aluminum | No | Medium |
| Tube aluminum | No | Light |
| Steel | Yes | Heavy |
| Wrought iron | Yes | Heaviest |

Wicker vs metal: how do they compare outdoors?
Wicker wins on comfort and soft, textured style, while metal wins on rigidity, easy cleaning and a modern, clean-lined look in outdoor furniture. Both handle rain well when they are the right type. The differences show up in sun, heat and what happens when the finish is damaged.
| Trait | Wicker | Metal |
|---|---|---|
| Rust | None on weave | Steel, iron |
| Heat | Often cooler | Hot in sun |
| Weight | Light | Varies |
| Upkeep | Moderate | Low-high |
| Look | Soft, warm | Sleek, classic |
Resin wicker rarely rots and shrugs off moisture, but the weave can fade, dry out or snag over the years, and dirt hides in the gaps. Metal frames wipe clean in a minute. Both depend on dry, ventilated cushions: foam that stays wet breeds mildew and ruins either style.
Does wicker furniture last outdoors?
Resin wicker lasts outdoors when the strands are UV-stabilized and fully weather-rated. Natural rattan and cane do not last: moisture makes them swell, mildew and split, and sun dries them until they crack. Expect the weave to age before the frame does.
Quality shows in the details: a tight, even weave, a rustproof frame, and strands described as UV-stabilized. Cheaper sets use thin strands that fade to chalky shades and fray at the corners within a few seasons of strong sun. Natural wicker belongs on a covered porch or indoors.
Which metal lasts longest outdoors: aluminum, steel or iron?
Aluminum lasts longest with the least effort because it cannot rust. Steel and wrought iron are strong and heavy but corrode when the finish is chipped and water reaches bare iron. Aluminum can chalk or pit in harsh conditions, which a wash and wax usually handles.
For coastal homes the choice is easier: salt air speeds up corrosion on iron-based metals, so powder-coated aluminum is the low-maintenance pick near the ocean. Further inland, a steel set with an intact finish is fine for years, provided chips are touched up early.
Hot metal in full sun
Dark metal frames and slats can get uncomfortably hot on summer afternoons. Cushions, a shade sail or a lighter finish make a big difference, and a woven resin surface often feels less hot to the touch, though no outdoor material stays cool in direct sun.

How does weather change the choice: sun, rain, wind and coast?
Match the material to your worst weather. Rain and moisture favor aluminum or resin wicker, salt air favors powder-coated aluminum, intense sun favors UV-stabilized wicker with shaded cushions, and wind favors heavier frames that will not blow across a deck.
| Climate | Best fit | Watch for |
|---|---|---|
| Rainy | Aluminum, wicker | Wet cushions |
| Coastal | Aluminum | Salt on steel |
| Hot sun | UV wicker | Fading, hot metal |
| Windy | Steel, iron | Chips, rust |
| Freezing | Aluminum | Trapped water |
Freeze-thaw cycles are hard on any material that holds water: water trapped in open tube ends or deep in a weave can stain or damage the finish over a winter, so store sets or cover them with a vented cover when temperatures drop.
How much maintenance does each material need?
Aluminum needs the least: a wash with mild soap and an occasional coat of wax. Resin wicker needs regular brushing and hosing to clear dirt from the weave, and steel or wrought iron need chip repair and waxing. Natural materials like teak add oiling or an acceptance of silver-gray weathering.
- Aluminum: wash with soap and water, dry, and wax once or twice a year if it chalks.
- Resin wicker: vacuum or brush the weave, wash with mild soap, and rinse well.
- Steel and iron: inspect for chips, sand and prime early, and keep the frame dry.
- Teak, for comparison: needs no finish and ages to gray, though some owners like to oil it.
Avoid pressure washing wicker at close range, which can pull strands loose, and skip harsh cleaners and steel wool on any powder-coated surface.
Which is better for small patios, cushions and comfort?
Wicker usually feels more comfortable because deep seats take thick cushions and the weave has a bit of give, while bare metal chairs are firmer and rely on slings or pads. Wicker sofas are bulkier than slim metal bistro sets, so check the footprint before buying.
A deep wicker loveseat can take more floor space than it seems, so measure first; our guide to how much space a conversation set needs gives clearance numbers for the walkways. Metal fits tight corners better with its thin legs and open frames, and lighter aluminum pieces move easily when you rearrange.
Is wicker or metal better for a fire pit area?
Metal frames suit seating near a fire pit more than wicker, because resin strands can melt or scorch from radiant heat or stray embers. Keep any wicker back from the flames, and follow the clearance guidance from the fire pit and furniture makers.
How do you choose between wicker and metal patio furniture?
Choose resin wicker on an aluminum frame if you want softness, comfort and a lived-in look, choose all-aluminum for the least upkeep, and choose steel or wrought iron only if you want weight and will keep the finish touched up. Always confirm the frame type before you buy.
A quick filter:
- Rainy or coastal home: powder-coated aluminum frame, either bare or wrapped in wicker.
- Strong sun: UV-stabilized wicker with light, ventilated cushions.
- Windy deck or rooftop: heavier steel or cast aluminum, anchored if needed.
- Little time for upkeep: all aluminum and quick-dry cushions.
- Covered porch or sunroom: natural wicker is acceptable here.
Whatever you choose, the frame metal, the coating and the cushion quality matter more than the headline material. Color matters too: lighter finishes run cooler in sun, and neutral tones suit most patio furniture styles.
Next in this series: How to Arrange Lava Rocks on a Gas Fire Pit: Rock Depth & Layers
Frequently asked questions
Is resin wicker or metal better for outdoor furniture?
Neither wins everywhere. Resin wicker on an aluminum frame gives the softest look and good weather resistance, while all-metal sets are tougher and simpler to wipe down. Aluminum suits rain and coasts, and steel or iron suit windy spots if the finish is kept up.
Does wicker furniture last outdoors?
Synthetic resin wicker does, because the woven strands are made for sun and rain. Natural rattan and cane do not, since moisture and UV make them crack, mildew and unravel. Expect the weave to fade or brittle first, usually before the frame gives out.
Which is more expensive, wicker or rattan?
Wicker is a weave, not a material, so the comparison depends on what it is woven from. Natural rattan furniture usually costs more than synthetic resin wicker, and a hand-woven piece costs more than a machine-woven one.
How long does powder-coated aluminum outdoor furniture last?
With basic care, powder-coated aluminum frames commonly last many years, often a decade or more, because the metal cannot rust. The coating is what wears: chalking and chips show up first, and a wash plus a coat of wax slows both.
What is the longest lasting outdoor patio furniture?
Teak, powder-coated aluminum and well-made resin wicker on an aluminum frame are the usual long-lasting choices. Teak ages to silver-gray and needs no finish, aluminum resists rust, and the right wicker resists UV when the cushions are kept dry.